Special thanks to Albany-Saratoga Speedway for opening up its track for our testing. Check
The modern-day C6 Corvette packs a serious punch from the factory, with the three available LS powerplants ranging from the 430hp LS3 ('08 and newer) to the 638hp LS9. And when that isn't enough, it's easy to open up a copy of VETTE and browse the latest go-fast goodies such as exhaust mods, camshaft upgrades, and even forced-induction systems. The lure of big power numbers eventually wears off, however, at which time it's a good idea to upgrade the suspension for better handling to complement the extra grunt under the hood. That's not to say the Corvette-of any generation-lacks in the handling department. Chevy's sports car has always been known for its prowess through the turns, and the latest C6 is no exception. But, as always, there's room for improvement.
Enter Pfadt Race Engineering. The company offers 15 different a la carte suspension upgrades for C5 and C6 Corvettes; we selected its adjustable coilover shock kit coupled with a set of C6 Z06 Corvette Racing sway bars (heavy-rate) front and aft to test on a serious street Vette.
The first step for Redline's Howard Tanner was to measure the ride height at all four corn
Our test vehicle is not the average Z06, as it's the flagship of Redline Motorsports, a high-performance Corvette and GM specialty shop located in Schenectady, New York. The silver C6 gets going in a hurry, thanks to a 432ci LS7 with an APS twin-turbo kit; all told, it cranks out 840-plus rwhp but can top 950 if the boost is cranked up and there's race gas in the tank. The car has gone mid-10s at 143 mph in the quarter-mile with Redline's Howard Tanner driving, on street tires, and granny-shifting the six-speed manual transmission. The power under the hood not only overpowers the Michelin Pilot Sport tires (345/30-19 back and 275/35-18 front, mounted on CCW 505A wheels) at the dragstrip, but also when Tanner pushes the Z06 hard through the corners on the highway and backcountry roads.
We began by stopping off at Albany-Saratoga Speedway (Saratoga, New York), to run the car on the asphalt oval and establish a baseline. The track recently upgraded from a dirt oval to a paved one as a way to attract street cars for special street nights and timed sessions. Using Albany-Saratoga Speedway served two purposes; first and most obvious was that it gave us a place to perform before-and-after testing to verify that the Pfadt parts were effective. The second reason was the paved oval offered us tight turns and no major straights, so Tanner couldn't get the car's blown stroker cooking. The oval is the closest representation of the average street thrashing at realistic speeds, thanks to corners that are similar to an off-ramp, a twisty highway, or a small parkway.
"The car barely sees track time, so I wanted to upgrade the suspension to something that was better performing on the street and rides nicer," said Tanner.
The front sway bar was easily unbolted and removed.
We established a baseline by making several runs and took our best back-to-back laps. The track officials told us that the regular street crowd measures its times in two-lap increments. Tanner's best two-lap time was 46.30 seconds. It wasn't bad considering the extreme heat during our test session (95 degrees on a sunny July day), and it was Tanner's first time around the oval. We then made the short trip to Redline Motorsports to swap over the parts and get back to the track for post-install testing.
The components are easy to install, and getting the car on a lift made it even easier, as Tanner; his brother, Derek; and Redline's head wrench, Bruce Hotaling, knocked it out in a few hours. This wasn't the first Pfadt coilover and sway-bar upgrade the shop had done, which certainly helped speed things along. The factory suspension setup uses a monospring that works well despite being introduced in the '60s. (Indeed, its effectiveness can be seen by the Vette's ability to pull 1g off the showroom floor.) The Pfadt coilover shocks replaced the front and rear monospring and stock shocks. That gave Tanner's Z06 a true independent suspension, with each wheel able to react on its own to any road condition.
The difference is obvious between the stock (bottom) and the Pfadt sway bar. The front OEM
The Pfadt bar offers a significant amount of adjustment, with firm and solid mounting. The
Pfadt sway bars are adjustable and use splined ends to hold the arms in place. They were a