All sorts of cliched comments come to mind when I think about my C5 Shark project. In some respects it's like a bad news-good news joke, or I could do a poor paraphrasing of the old Star Trek "going boldly where no one has gone before" line. Maybe "if I'd only known then what I know now" would be apropos. Regardless, I made a commitment to this concept-an LS1 and 4L60E installed in a third-gen Corvette-nearly two years ago, and sealed the fates of both myself and what I originally nicknamed the (not so) Great White when the '76 Stingray's L48 small-block and Turbo 350 went to a new home in a needy '68 Camaro.
As I've outlined before, ain't nuthin except being a General Motors V-8 engine and bore spacing that's common between the venerable and beloved Chevy small-block and GM's Gen III that, in various configurations, is found in Corvettes, Camaros, Firebirds, and pickup trucks. Boy, does that ever make things interesting!
Last month I mentioned that Bow Tie Overdrives, a Southern California company that specializes in 700-R4 swap kits for older Chevy (and other GM) products, was handling not only the details of installing a 4L60E in the old Shark but had also volunteered to take a stab at making the LS1 fit.
While the final transmission crossmember will be very similar to what we showed in last month's installment, the motor mount setup of just a few weeks ago turns out to have been the first of several concepts that the boys at B.T.O. tried and tossed before coming up with what we'll show right now as templates for the "stands" that are being fabricated as this is written. Using an adapter plate with traditional 350 small-block side mounts and custom frame stands-as shown last month-are completely out of the picture. The final setup utilizes F-body LS1 mounts in the factory location, bolting directly to new, custom stands that will be welded to the frame. The custom LS1 stands also straddle both the steering box (on the driver's side) and the idler arm (on the passenger side), and are designed to allow full access to the steering components and the hardware that affixes those components to the frame.
The centerline of the LS1's crankshaft and the driveline are essentially identical to the factory's alignment of the original 350/TH350. With the GM Performance Parts LS1 and 4L60E (PNs 25534322 and 12497318) mocked up in what will be within hundredths of an inch of their final locations, B.T.O. has confirmed that the stock '76 power steering ram barely clears the oil pan; that the F-body LS1 exhaust manifolds fit very well within the old Corvette's frame, steering box, and column; and we know for certain that the accessories (power steering pump, air conditioning compressor, and alternator) will not fit in either C5 or F-body configurations.
One of Bow Tie Overdrives' technicians holds a template for final version of the driver's side motor mount stand. The faint lines on the side of the template near Jason's right hand indicate where the windows will be.
So, the engine and transmission mounts are pretty much finalized. Next month we should be able to show both the finished trans crossmember and the motor mount stands welded in place in the C5 Shark's frame. We've removed the original gas tank and shipped it off to Rock Valley Antique Auto Parts, a company well known and highly regarded in the street rod hobby for their stainless steel gas tanks, to be replicated in stainless and completely set up (wiring, fittings, in-tank-and correct-electric fuel pump with filter, baffling, etc.) to fit in the '76 and work with the LS1. Once we have the new gas tank we'll start fabricating the new fuel lines.
Meanwhile, the Shark's original radiator is in position and, once a couple of cooling system fitment problems are resolved, will become a mock-up for where hoses and lines need to be located on a new and, naturally, custom radiator to fit the '76 Corvette's core support and work properly with the LS1.
We'll be back next month with another update on the progress of the C5 Shark. With any luck at all, we can show the old and new fuel tanks, the mock-up for the radiator, and a trick, workable, and custom solution to the accessory mounting problem. The LS1 engine swap has proven to be much more complex than we'd expected. But what has been and is still being learned will ultimately be seen as a kit (or series of kits and components) that'll make it possible for owners of '63 through '82 Corvettes to install the incredible LS1 in their cars without going to a drastically modified frame and suspension (i.e. Car Creations' C4 suspension conversions), and without starting from scratch like we've done. See ya on the next lap.