Dave Semel's '58 Corvette...
Dave Semel's '58 Corvette combines C5 technology with the '58's classic style.
re•dux |rē-dəks; 're-dəks|
ORIGIN Latin, returning, from reducere, to lead back. First known use: 1860.
(Definition courtesy Merriam-Webster online dictionary, www.merriam-webster.com)
The word "redux" describes not only Dave Semel's restomodded '58 Corvette, it also describes the '58 Corvette itself.
Semel kept the '58's trunk...
Semel kept the '58's trunk spears, which set off the Midnight Blue Pearl paint.
For Corvette's sixth year, upgrades were in order. Outside, a longer front end now featured four headlights and a nine-tooth grille, while the hood gained a set of simulated louvers, the trunk lid gained a pair of longitudinal chrome spears, and all Vettes were now painted with acrylic lacquer paints. Inside, an all-new dash went in, as did restyled seat upholstery and door panels. Mechanically, the Borg-Warner T-10 four-speed was available from Day One, and the highest-output 283 fuelie saw its horsepower rating bumped up to 290.
In a year when steel-bodied Chevy production was down around 20 percent, Corvette sales jumped to 9,168—up nearly a third from 1957—making it the only one of The General's car lines to show a sales uptick for 1958. It probably helped that the Vette had no domestic sales competition, since Ford had ended two-seater Thunderbird production in December 1957.
Think it's a stock '58 inside?...
Think it's a stock '58 inside? Think again—the seats are Wise Guys custom buckets, and the steering wheel's an Al Knoch repro.
The '58 that Dave Semel turned into the VetteRod you see here needed more than some simple upgrades. It needed "reduxing" in the biggest way. "It was just the body from the firewall back, and it had an old, rusted-out frame," says Semel of the C1 that had sat in an Alabama field for over two decades, and whose body—what there was of it—needed a lot of fiberglass work.
Many Corvette builders would have turned away from it, and some would have run away as fast as they could. Not Semel. He saw the potential in it. "I knew that I wanted to do a restomod, but something that was a little bit different than what other people had done." One that would have all the hardware from a fifth-generation Corvette underneath that vintage fiberglass.
Semel had been inspired by a first-gen Vette restomod that he saw at Corvettes at Carlisle, and he found a builder that was willing to work with him on it. Unfortunately, about five months in, Semel and that builder parted ways when Semel realized that the builder couldn't handle the project.
This build photo by Semel...
This build photo by Semel shows how much custom work was needed to make the body clear the six-speed gearbox.
Eventually, Semel got in touch with Jerry Smith at Southern Street Rods and Corvettes in Ft. Pierce, Florida. "He got all the measurements, did all his own engineering, and built the frame so we could take most of the components from an '00 Corvette donor car and put them directly onto [it]," he recalls.
That frame had one big difference from other C1 restomod frames: where the engine would sit in the engine bay. It was built so that an LS-series engine would sit low, a boon to weight distribution and handling, as was the rearward location of the C5's gearbox. "With the transmission in the back, we were able to get this car to have 50/50 weight distribution," Semel adds. Smith's frame design enabled the use of just about every chassis, steering, and suspension piece from the donor C5, though QA1 coilovers did go on at each corner.
The '00 Vette's rear-mounted six-speed presented some challenges when it came to fitting the '58 body over it. The trunk had to be cut out and refashioned, so that it would clear the new transmission, while looking every bit a '58 original. (Same with the transmission/driveshaft tunnel, enlarged to make room for the C5's torque tube.) In all, the 'glass work—by Johnny Cano and Norm Church in Ft. Pierce, and completed by Tony Stanz and Mike Hacker at Back-In-Time in Bethlehem, Pennsylvania—made the '58's body look like it came out of St. Louis configured this way.